Setek WiFi Extender Setup

To get the best out of your WiFi extender, you must execute the Setek WiFi extender setup accurately. The correct setup will extend the coverage of your existing WiFi network beyond its usual range. If you fail to proceed with the Setek SE-01 WiFi extender setup correctly, the extender won’t work efficiently. Therefore, you must set up the extender using the exact Setek WiFi extender setup instructions.

Today, we have brought you the ultimate post with the complete Setek WiFi range extender setup procedure. To find out thoroughly, keep reading ahead!

How Do I Setup My Setek WiFi Range Extender?

Apparently, there are two ways to proceed with the Setek SE-01 WiFi extender setup. You can either set it up using the IP address or the WPS button. To set up the extender using the former method, you will require the correct IP address, default username, and password of the extender. The Setek WiFi extender setup instructions are as follows:

Setek Superboost Extender Setup by IP Address

Initially, place the extender and router in the same room, and connect your PC or mobile to the extender’s network.
You can form the connection using the Ethernet cable or wirelessly.
On that device, go to any web browser, and enter the IP address of the extender.
Now, the login page of the extender will appear.
After that, enter the default username and Setek WiFi extender setup password in the given fields.

You can find the default login credentials on the label of the extender.
Now, the user interface of the extender will appear.
Hereon, you will need to select the SSID of your router and enter the password to form a connection.
When the Setek WiFi range extender Configuration is complete, the device will automatically reboot.
After the reboot, you can locate the extender someplace else.

Setek WiFi Extender Setup Through WPS Method

Firstly, ensure the extender and the router are in the same room.
Secondly, find the WPS button on the extender and the router.
After that, press the WPS button on the router.
Now, within the next two minutes, press the WPS button on the extender.
Give the router and extender a little while to form a connection.
When the connection is successful, you can relocate the extender.
Ensure to find the most suitable location for the extender.

Troubleshooting the Setek Superboost WiFi Extender Setup Issues

If you were unable to configure Setek WiFi extender accurately, you will need to try again. However, this time, there are a few things you must keep in mind to ensure a proper Setek SE-01 WiFi extender setup. These tips are as follows:

Power On the Router and Extender

Before you proceed with the Setek WiFi Extender setup, you must power On both devices.
Ensure to plug the devices into a stable and working power source.
You must place the extender and the router in the same room as well.
If the router and the extender are too far, the connection will fail.

Connect your Device to the Extender’s Network

To set up your extender correctly, need to connect your device to the extender’s network.
Otherwise, you cannot log into the extender’s network.
If you are using an Ethernet cable to establish a connection, check the cable connection.
Ensure to plug the cable into the router and the PC correctly.

Relocate the Extender

After the Configuration , you can place the camera near the dead zone.
However, you need to make sure the extender isn’t too far from the router.
If you place the extender outside of the router’s range, the connection will break.
Therefore, ensure to place the extender, where it’ll receive the router’s network.

Fixing the Login Issues

If you are unable to log into the user interface, you can resolve it easily.
You will need to use the correct IP address of the extender to access the login page.
To find out the right IP address, go to start on your PC.
After that, enter ‘cmd’ in the search box and press enter.
Now, type ‘ipconfig’ on the screen and press enter.
At last, next to ‘Default Gateway’ you can find the IP address of the extender.
There could be an issue with the web browser as well.
Before logging in, clear out the cache of the browser and disable any firewall to log in.
Ensure that you are using an up-to-date web browser only.
To log in successfully, make sure you are using the accurate username and Setek wifi extender password.

FAQs

How do I connect my Wi-Fi extender to my router?

If you have been wondering how do I setup my Setek WiFi range extender. You can connect your extender to your router through the WPS method or the web browser method. The WPS method is the quickest and easiest method to connect your extender to the router. However, if your router doesn’t have a WPS button, you will have to set it up using the web browser.

How to Reset the Setek WiFi extender?

You can reset the Setek WiFi extender using the following steps:

Primarily, find the extender’s reset button.
Now, press the reset button on the extender.
After 10-12 seconds, let go of the reset button.
Hereon, you will need to log into the extender’s user interface.
Thereafter, go to the ‘Management’ tab.
Finally, click ‘Factory Reset’ to complete the reset.

What happens when I press the WPS button on my router?

When you press the WPS button on the router, the router will scan for any network to connect to. You can use this method to connect the extender to your router. Ensure to place them both in the same room to establish a connection successfully.

What are the modes on the Setek Wi-Fi extender?

The Setek WiFi extender offers several modes to users. These modes are as follows:

Wireless router mode
Repeater mode
Client mode
Access point mode
Wisp client router mode

We hope you have understood how to setup Setek WiFi extender. We have also discussed the ways to troubleshoot any issues you could face during the installation . However, if there are any other issues you are facing with your Setek WiFi extender, reach out to our team!