How to Setup Madpower WiFi Extender?

A Mappower WiFi extender is an excellent investment for your house or workplace. You just need to set it up using the re.madpower.home address, and you’re all set. However, to make the most out of your device, you must set up your Madpower WiFi extender accurately. It’s essential to set up the extender properly, as improper setup can cause critical issues within the range extender. Moreover, the correct setup will eliminate the dead zones in your house. You can take help from the Madpower WiFi extender manual to set up the extender

Madpower Wifi Extender Setup

However, if you find the manual too lengthy to go through, don’t worry! We have brought you the ultimate Madpower WiFi extender setup guide via the http //re.madpower.home address. To learn the whole procedure thoroughly, keep reading ahead!

Requirements for the Madpower WiFi Extender Setup

A setup router
The Madpower WiFi extender
Re.madpower.home web address
A mobile phone or PC

Methods for the Madpower WiFi Extender Setup

If you want to know how to setup Madpower WiFi extender, there are two methods for it. You can set up the extender through the re.madpower.home web address or the WPS button. The procedure for these methods is as follows:

Madpower WiFi Extender Setup Via http //re.madpower.home

To begin with, plug the WiFi extender into a power source around your router.
Ensure the power LED is On and solid.
Now, connect your device to the extender’s network.
You can use an Ethernet cable to establish a connection or connect it wirelessly.
Once the connection is complete, enter http //re.madpower.home in the address bar.
Now, the setup page of the extender will appear on the screen.

After that, you can follow the instruction to set up your extender.
Hereon, enter the router’s network and password to form a connection.
When the setup is successful, the extender will reboot to bring the changes into effect.
At last, you can unplug the extender and relocate it to the area where you receive poor coverage.
Ensure to plug it into a stable power source and that the LED light is on.
Now, you can connect to the extender’s WiFi network again.

Madpower WiFi Extender Setup Via the WPS Button

Firstly, turn on the router and the extender and place them in the same room.
Find the WPS button on the router and the extender.
Now, press the WPS button on the router and hold it till the WPS light starts blinking.
After that, press the WPS button on the extender within two minutes.
You can release the WPS button when the WPS light starts flashing.
When the WPS light stabilizes indicates the connection is successful.

Finally, you can relocate the extender to the desired location.

We hope you were able to understand how to setup Madpower WiFi extender. When you are setting up your WiFi extender, you can refer to this Madpower WiFi extender manual. Now, you can set up your extender via the http //re.madpower.home address and the WPS button.

Methods to Fix the Madpower WiFi Extender Setup Issues

Sometimes during the setup, various issues arise due to some factors. You can troubleshoot this issue by following the below ways:

Inspect the Power Outlet

For the setup, the router and the extender require a stable power source.
If either device is off, the setup won’t be successful.
Therefore ensure to plug both devices into a working electrical outlet.
If the current socket isn’t working, you can try plugging them into a different outlet.

Establish a Connection

To set up the extender, you must connect your device to the extender’s network.
Without a connection, you cannot set up the extender.
If you are using an Ethernet cable to establish a connection, check the cable.
Ensure you are connecting to the correct network SSID, which is ‘Madpower_Extender’.
You can refer to the above Madpower WiFi extender to learn the process to establish a connection.

Move the Extender Closer to the Router

During and after the setup, the location of the extender matters a lot.
While setting up the extender, you must ensure that the extender and the router are in the same room.
When you are done with the setup, you must choose the most suitable spot for the extender.
While choosing a location, you must keep in mind that the extender should be in the router’s range.
If you place the extender too far from the router, the extender will have difficulty receiving the router’s network.
Therefore, ensure to place the extender halfway between the router and the dead zone.

Use the Correct IP Address/Web address

You can only access the setup page through the IP address and http //re.madpower.home.
If you are using the IP address, ensure you are using the correct IP address.
You cannot access the setup page using the wrong IP address.
To find the correct IP address, connect your PC to the extender’s network.
After that, go to start and type ‘cmd’ in the search box.
Now, type ‘ipconfig’ on the screen.
Next to the default gateway, you can find the IP address of the extender.

Ensure to try these methods accurately to fix the setup issues. Before you try any troubleshooting method, ensure to check your Madpower WiFi extender manual.

FAQs

What is a Madpower WiFi extender?

The Madpower WiFi extender is a networking device that amplifies the coverage of your current WiFi network. It connects with your router and broadcasts it to all the areas that the existing router isn’t able to deliver to.

What should I do if the WPS method doesn't work?

If you are unable to set up the extender via the WPS button, you can set it up using the http //re.madpower.home address. We have discussed the complete procedure in the above section. Follow the steps carefully to set up your extender. If the WPS method isn’t working, ensure the extender and the router are on and in the same room.

Why is my Wi-Fi extender not connecting?

If the extender isn’t connecting to the router, you can reset it. The steps for the reset are as follows:

Firstly, locate the reset button on the extender.
Now, press the reset button using a sharp object or something similar.
After 10 seconds, you can let go of the button and let the device reboot.
When the device turns back on, the factory default settings will be back.
At last, you can reconfigure the extender again.

These are the steps to reset the extender.

We hope you learned how to setup Madpower WiFi extender. If there are any issues you are facing with your extender, you can resolve them by following the methods. However, if you are having any other difficulties, you can contact our team!